07/10/07@
512-00461A@ Bar Flag@Prevents plates from scratching@
512-00462A@ Replacing the tweezers on Lotem 800 Family platesetters.@
512-00314A@ Replace the tail gripper springs.@
512-00416A@ Install the Creo Feature Licensing Server (CFL) to provide feature control management for multiple applications.@
512-00387A@ Install a carriage amplifier with a cooling element on a Lotem 800 II (Type I) platesetterr.@
512-00351A@ Upgrade the existing load roller to a one piece load roller.@
512-03310A@ Add a power failure protector board.@ To prevent damage to machine components due to an electrical power surge, add a power fail protector board to maintain the machine in an Off status until the On/Off pushbutton is toggled.@
512-03285A@ Local3 box assembly.@ Prevent the Local3 board does not respond error message, by adding a capacitor to the Local3 board's reset circuit.@
512-01636@ New bar flag design.@ The new bar flag design and grounding cable are not affected by electrostatic electricity.@
512-01322@ Attach a Teflon strip to the punches' covers.@ Prevents the edges of the plate cover from scratching the plates and reducing the quality of the printed images.@
512-00254@ Front and rear door gas spring pistons replacement.@ Enable the front and rear doors to open properly.@
512-00254A@ Front and rear door gas spring pistons replacement.@ Enable the front and rear doors to open properly.@
512-00222A@ XY vacuum pump.@ Replace the existing XY vacuum pump with the low maintenance vacuum generator. Unlike the existing vacuum pump, a vacuum generator has been designed that does not require planned maintenance every six months, and therefore the service costs are greatly reduced. @
512-00213A@ Suction cup assembly.@ A suction cup assembly has been designed that can be replaced by the customer. The engineer however, will initially have to install the new assembly. Thereafter customers can replace their platesetters suction cups without having to place a call to the Response Center.@
512-00207A@ Replace the existing paper/plate detector.@ Replace the existing paper/plate detector with a wide range detector. The wide range detector can detect a wide range of plates without the need for calibration.@
512-00141A@ Accessories CD.@ To improve the support of the Lotem devices, install the support tools from the Accessory CD.@
512-00133A@ Replace the existing shoulder screws with self locking screws.@ Over time, the shoulder screws on the tail gripper may loosen and break off.@
512-00121A@ Install a new design of middle lever with extended arms.@ The previous middle spring spoilers were not durable enough and failed to make the spoilers rise high enough above the drum to successfully unload a plate. The new middle lever solves both these problems.@
512-00120A@ Install a new design of middle lever with extended arms.@ The previous middle spring spoilers were not durable enough and failed to make the spoilers rise high enough above the drum to successfully unload a plate. The new middle lever solves both these problems.@
512-00106@ Replace the drum load rollers and drum roller springs with the new drum roller spring unit.@ When a plate is improperly loaded or a plate fly-off occurs, both the drum rollers and the drum roller springs disperse inside of the Lotem.@
512-00092A@ Replace the air nozzles with silicon cups.@ The existing air nozzles on the platesetter can damage the plastic washers inside the cassette air fitting assemblies and eventually lead to plate and paper separation failures. This FCO improves the platesetter/cassette interface by replacing the air nozzles with silicon cups.@
512-00091A@ Replace the plate on unload detector.@ Replace the plate on unload detector with an enhanced detector(p/n 504S1L783A).@
512-00044 @ Replace the DC conveyor motor with encoder.@ Enables the conveyor to receive plates as they are unloaded from the Lotem.@
510F29167@ Replace the drum load rollers/drum roller springs with a new drum roller spring unit.@ When a plate is improperly loaded or a plate fly-off occurs, both the drum rollers and the drum roller springs disperse inside of the Lotem.@
510F29150B@ 69mm Punch cover replacement.@ Solves problem of proof loading arm or 0.15mm plates colliding with the punch.@
510F29150A@ 50mm Punch cover replacement.@ Solves problem of proof loading arm or 0.15mm plates colliding with the punch.@
510F29150@ 29mm Punch cover replacement.@ Solves problem of proof loading arm or 0.15mm plates colliding with the punch.@
510F28983@ Debris removal kit installation.@ Removes ablation as it is created.@
510F28844@ Replace the standard unload roller assembly with an unload roller assembly that includes a single roller.@ To curtail repeated problems with pressure marks that are caused by the unload rollers.@
510F28598@ XY suction manifold valve stopper installation.@ To prevent intermittent plate pickup failure, install a valve stopper in the pressure/vacuum unit assembly valve.@
510F28534@ Anti-scratch rollers and centering pin rubber rings, installation.@ Reduce plate slide-back effect during loading.@
510F28534@ Anti-scratch rollers installation.@ Prevent slide back effect with anti-scratch rollers that raise friction coefficient between plate and rollers.@
510F28458@ Light detector, hood with lens brush installation.@ Prevent decline in image quality and diode function caused by plate ablation accumulating on optic head lens protector and light detector lens.@
510F28354@ Power distribution board, comp level Q inventory replacement.@ Change board part number to reflect comp level.@
510F28271@ Load roller assembly, roller flange replacement and adjustment.@ Resolve loading problems due to different tolerances in machines, by enabling load roller adjustment.@
510F28102@ Vacuum pump, wet pump to dry pump replacement.@ Curtails repeated problems related to oil leakage, including poor plate attachment and hot spots.@
510F28061@ X and Y motors, adapter cable replacement.@ Prevent noise entering motor encoders, which causes motor to lose location and leads to loading problems.@
510F28007@ Paper disposal door interlock, cover installation.@ Prevent damage to interlock wiring when paper sheets are removed from paper bin.@
510F27958@ Preload position sticker - installation.@ Shows customer specific location of the preload.@
510F27928@ Short pin assembly replacement.@ Solve intermittent misregistration problems resulting from improper short pin assembly.@
510F27847@ Gripper actuator needle bearing replacement for the Lotem 800 VL.@ Extend life of actuators and improve gripper reliability.@
510F27835@ Unload tray rollers; regular tray; roller replacement.@ Improve rollers reliability and increase unload force by 10-30%.@
510F27707C@ 29mm Punch motor HP detector, holder replacement.@ Improve punch HP detector adjustment and improve punch system reliability.@
510F27707B@ 69mm Punch motor HP detector, holder replacement.@ Improve punch HP detector adjustment and improve punch system reliability.@
510F27707A@ 50mm Punch motor HP detector, holder replacement.@ Improve punch HP detector adjustment and improve punch system reliability.@
510F27707@ 29mm Punch motor HP detector, holder replacement.@ Improve punch HP detector adjustment and improve punch system reliability.@
510F27648@ Spring spoilers and head gripper assembly replacement.@ Solve plate unloading problems and attachment problems near head spoilers, and support wide range of plate thickness.@
510F27647@ Local 3 box replacement.@ Prevent electric short on Local board and prevent Local 3 pins from bending or being damaged.@
510F27501@ Unload tray rollers, GTO, replacement for small plates.@ Improve GTO rollers reliability and increase unload force by 10-30%.@
510F27494@ Plate support, replacement for 0.15mm plates.@ Improve machine reliability for thin plates.@
510F27488B@ Vacuum and swivel hose replacements.@ Increase loading reliability with improved vacuum hose and new swivel-hose interface.@
510F27390@ Plate supports, shoulder screws replacement.@ Improve reliability of 0.15 plate loading and solve problem with releasing screws.@
510F27384@ V block, oiling kit bracket installation.@ Chain base bracket presses on oiling kit bracket causing friction between carriage and V groove, leading to unwanted lines on image.@
510F27343@ Centering motor, spring pin replacement.@ Prevent cutting spring pin in sprocket and improve centering system reliability.@
510F27281@ Punch motor replacement.@ Improve punch motor efficiency, prevent motor from getting stuck when double loading occurs, and improve punching for 0.4-mm plates.@
512-02139A@ Connect a closed circuit connector to each of the Local3 boards.@ Connect a closed circuit connector to the Local3 boards in order to prevent two conflicting components within the platesetter from generating error messages.@
510F25223@ Suction cups, large - replacement.@ Replace the loading system suction cups with bigger cups for better suction to plates. Newer cups improve plate transfer from short pins to the drum.@
512-00470@ carriage amplifier board replacement@Improves the power supply to the carriage amplifier board by replacing both the J1 and J3 connectors.@
512-01395@Debris removal air pressure sensor tube connection@Monitors the UDRC flow rate by connecting the debris removal air pressure sensor tube to the MCE board.@
510F28442@ ANTI COLLISION KIT FCO-DLC@ Improve reliability of cassette centering system; prevent plates from moving under centering arms; prevent collisions between suction cups and centering arms on certain plate sizes.@
512-00105@ DLC and Lotem bypass board connector, grounding.@ Ground the DLC bypass board to prevent static electricity.@
512-01485@ DLC roller bearings.@ New design for the DLC tray holder assembly.@
510F27624A@ DLC, connector assembly replacement. @ Lower DLC connector to improve connection with opposite contactors.@
510F27753@ DLC, improved contacts, board replacement.@ Improve durability of connector.@
510F27624@ DLC, upper tray stopper installation.@ Prevents upper tray from sliding beyond its out position and thus keep tracks from breaking apart.@
512-00181A@ Dual-loading cassette (DLC) system.@ Install the improved DLC centering arms with the paper/plate separation brackets. The improved centering arms and brackets cause the plate to convexly bend. The convex bending forcibly separates the plate from any slip sheets that are immediately above and beneath the plate.@
510F27184@ Cassette interlock sensor, adjustable bracket replacement.@ Prevent opening of interlock system loop caused by sensitive cassette interlock sensor.@
510F27885@ Cassette light seal; option for multiple cassettes, installation.@ Create storage place for cassette seal when cassette is inside machine.@
510F27456@ Cassette, anti-static kit installation..@ Prevent double loading and loading of plate with paper, by reducing electric static power.@
512-00182A@ Install the improved SLC centering arms with the paper/plate separation brackets. @The improved centering arms and brackets cause the plate to convexly bend. The convex bending forcibly separates the plate from any slip sheets that are immediately above and beneath the plate.@
512-02139A@ MCU - Connect a closed circuit connector to each of the Local3 boards.@ Connect a closed circuit connector to the Local3 boards in order to prevent two conflicting components within the platesetter from generating error messages.@
512-00661@  MCU - Add a new 220V safety outlet with OPS option.@ Replace the exposed 220V open/close outlet.@
512-00508@  MCU - Anti scratch for the DLC Spectrum cassette. Replace the rollers on the proof loading bar with soft rollers.@ This FCO prevents the rollers on the proof loading bar from scratching plates during loading.@
512-00183A@ MCU - Improving the multi-cassette units plate/paper separation@ The improved centering arms and brackets cause the plate to convexly bend. The convex bending forcibly separates the plate from any slip sheets that are immediately above and beneath the plate.@
510F29049A@ MCU - Kit2 Installation of a stronger center part assembly on the user door and reinforcements on each tray.@ MCU for Lotem 800 user door and cassette tray reinforcement.@
510F29049@  MCU - Kit1 Installation of a stronger center part assembly on the user door and reinforcements on each tray.@ MCU for Lotem 800 user door and cassette tray reinforcement.@
510F28440@  MCU - ANTI COLLISION SUC. KIT ASSY@ Improve reliability of cassette centering system; prevent plates from moving under centering arms; prevent collisions between suction cups and centering arms on certain plate sizes.@
512-00106A@ VL - Drum load rollers and roller springs replacement for the Lotem 800 VL.@ To prevent the rollers and springs from scattering inside the Lotem800VL, replace the drum load rollers/springs with new drum roller spring unit.@
512-02637@  VL - Improving the unload force on the Lotem 800 VL tray.@ The edges of small plates cut the rollers as they pass through them.@
512-28458A@ VL - Light detector, hood with lens brush installation.@ Prevent decline in image quality and diode function caused by plate ablation accumulating on optic head lens protector and light detector lens.@
512-02635@  VL - Replace the unload roller assembly with a single-roller assembly on the Lotem 800 VL.@ Reduces the number of repeated service calls for recurring pressure marks, and increases machine reliability by replacing the current unload roller assembly with one that has only a single roller.@
512-02638@  VL - Repositioning the spring spoilers on the Lotem 800 VL.@ The drum on the Lotem 800 VL is larger than that of the Lotem 850. Therefore the spring spoilers need to be repositioned to solve the attachment problem near the head spoilers and to ensure that the plates unload correctly.@
END;